#ESU PASSWORD CHANGE GENERATOR#
#ESU PASSWORD CHANGE UPDATE#
#ESU PASSWORD CHANGE PASSWORD#

#ESU PASSWORD CHANGE UPDATE#

Important: Following this change you will need to update any saved passwords on your web browsers, e-mail clients, and other places that you have stored your NetID credentials.

#ESU PASSWORD CHANGE PASSWORD#

Press the button labeled Set Password and/or Questions.In the event that you forget your NetID or password, these questions can be used to recover your account. It is highly recommended that you configure your recovery questions.Scroll down to the section labeled SET RECOVERY QUESTIONS.Under the section labeled SET RECOVERY EMAIL, if 'Recovery Email' is blank, enter your personal (example email address. Prior to changing your password, you will be required to set your recovery email address is you have not done so already.Re-enter your password on the next line to confirm.Enter your new password making sure to follow the password requirements listed above.Scroll down the page until you reach the section labeled CHANGE YOUR NETID PASSWORD.Navigate to and login with your current NetID and password.Designed to meet UL and CSA specifications. Also available in a 220-240 volt, 50-60 Hz configuration. The alarm tones are not adjustable and are set at 65 dB minimum at 1 meter. To assure your computer experience at East Stroudsburg University is a positive one, the Academic Computing Help Desk is available to assist you with your computer and technical questions and concerns. The mode indicator tones are adjustable to a minimum level of 45 dB at 1 meter. For example, if the initial impedance is 30 ohms, the upper level trip is approximately 42 ohms. Acceptance range is 5-135 ohms after REMВ° PolyHesiveВ° II return electrode is applied.Measurement Frequency: 140 kHz В± 20 kHz.Power ReadoutsДЄgree with actual power into rated load to within В± 15% or 5 watts, whichever is greater. Current is less than 8 amperes in cut and less than 4 amperes in coag. Less than 150 mA rms Input Power Requirements Sink current, 140V applied, all inputs Normal polarity, intact chassis ground Low Frequency Leakage (50-60 Hz) Source current, patient leads, all outputs tied together. Bipolar: 510 kHz sinusoid Output power changes by less than 5% or 5 watts, whichever is greater, as the line voltage varies from 85-135 volts (into a 300 ohm load).Coag: 510 kHz damped sinusoidal bursts with a repetition frequency of 31 kHz Low Voltage 510 kHz sinusoidal bursts at 25%.Blend 3: 510 kHz sinusoidal bursts at 25% duty cycle recurring at 31 kHz.Blend 2: 510 kHz sinusoidal bursts at 37.5% duty cycle recurring at 31 kHz.Blend 1: 510 kHz sinusoidal bursts at 50% duty cycle recurring at 31 kHz.Valleylab REMВ° safety has been proven in more than 100 million surgical procedures worldwide.

#ESU PASSWORD CHANGE GENERATOR#

If a fault in the patient/return electrode contact is detected, the REMВ° system automatically deactivates the generator virtually eliminating the risk of burns under the return electrode. Is guaranteed with Valleylab's patented adaptive REMВ° system, which continually monitors patient impedance levels. Low Voltage CoagulationД®nsures controlled, precise desiccation with less destruction of peripheral tissue, making the ForceВ° 2 generator ideal for laparoscopic procedures. Accessories are activated only when keyed, reducing the potential for injury caused by inadvertent activation. Permits two surgeons to fulgurate from a single generator, for added convenience and efficacy. Provide flexibility through varying degrees of hemostasis. Refurbished units are available from Avante Health Solutions. A monopolar foot switch is included, a bipolar foot switch is optional as is a rolling cart. 300 watts is available for output in the cut setting. The REMв„ў (Return Electrode Monitoring) is standard. The generator hasВ audible and visual alarms, including REMв„ў Fault Indicator. The Valleylab Force 2 electrosurgical unit is a long standing work horse and provides cutting and coagulation in monopolar or bipolar outputs.

Esu password change